Father’s Day Sale: 15% off Sitewide w/code DAD15 (excludes sale items / ends Sun 6/21 at 9pm CST)
ANNIV40 for 40% OFF sitewide (no stacking, no sale items) ANNIV40 for 40% OFF sitewide (no stacking, no sale items) ANNIV40 for 40% OFF sitewide (no stacking, no sale items) ANNIV40 for 40% OFF sitewide (no stacking, no sale items) ANNIV40 for 40% OFF sitewide (no stacking, no sale items)

What Is Bacteriostatic Water?

Bacteriostatic water is water for injection with benzyl alcohol added as a preservative, 0.9% (9 mg per mL) in a standard 30 mL vial, so one container can be entered more than once. Hospira’s licensed version, on DailyMed, is labelled sterile and nonpyrogenic, with a pH of 5.7 (range 4.5 to 7.0) and storage at 20 to 25 °C.

Renovita Research sells Bacteriostatic (BAC) Water-30ml (RESEARCH USE ONLY) for laboratory research, with a certificate for its lot. Updated 17 November 2026: below is how bacteriostatic water differs from sterile water, how long it lasts once opened, what that certificate tests line by line, and what published studies show about benzyl alcohol and dissolved proteins.

Key Takeaways

  • Bacteriostatic water is water for injection with 0.9% benzyl alcohol. Sterile water for injection has no preservative and is supplied only in single-dose containers.
  • The Hospira label prints no time limit after first puncture. The 28-day figure comes from USP General Chapter 797, the pharmacy standard for sterile compounding.
  • The certificate for Renovita Research’s 30 mL lot EBC2610-RR-BWP-1005 confirms benzyl alcohol by LC-MS/MS at 0.92%, inside its printed limit, and lists sterility as not tested.
  • Benzyl alcohol at 0.9% made several dissolved proteins aggregate in published studies. Those studies used full-size proteins, not short research peptides.

What is bacteriostatic water made of?

Bacteriostatic water is two ingredients: water for injection and benzyl alcohol. Bacteriostatic means the preservative holds back the growth of bacteria; it does not sterilize anything that enters the vial later. The Hospira label describes a multiple-dose container from which repeated withdrawals may be made, and calls the water nonpyrogenic, meaning free of fever-causing contaminants such as bacterial endotoxins.

What a vial holds, by that label:

  • Water for injection, chemically H2O.
  • Benzyl alcohol, 0.9% (9 mg/mL) in the 30 mL plastic vial. Hospira also lists a 20 mL fill in a 30 mL glass vial at 1.1% (11 mg/mL), so the percentage printed on the vial tells the two apart.

The label lists no buffer and no salt.

Research peptides, such as those on Renovita Research’s peptides page, are supplied as lyophilized powder, and bacteriostatic water is the solvent that turns that powder back into a solution.

BAC water vs sterile water and saline

BAC water, sterile water and normal saline differ in a preservative and a salt. Hospira’s Sterile Water for Injection label and its 0.9% Sodium Chloride Injection label both state no bacteriostat, antimicrobial agent or added buffer, and single-dose containers only. Saline adds 9 mg of sodium chloride per mL, which makes it isotonic. Hospira’s Bacteriostatic 0.9% Sodium Chloride label combines the two: saline with the same 0.9% benzyl alcohol, in a multiple-dose vial.

Bacteriostatic waterSterile water0.9% salineBacteriostatic saline
Benzyl alcohol0.9% (30 mL vial)NoneNone0.9%
Sodium chlorideNoneNone9 mg/mL9 mg/mL
ContainerMultiple-doseSingle-dose onlySingle-dose onlyMultiple-dose
SourceHospira labelHospira labelHospira labelHospira label

All four labels describe the solution as sterile and nonpyrogenic. The bacteriostatic water label notes that some drugs may be incompatible in a vehicle containing benzyl alcohol.

How long does bacteriostatic water last once opened?

Bacteriostatic water has no in-use period on the Hospira label. The label gives the storage range and an expiry date for the sealed vial, and nothing about days after first puncture.

The 28-day figure comes from USP General Chapter 797, the United States Pharmacopeia standard for compounding sterile preparations. USP’s 2023 FAQ on that chapter says a conventionally manufactured multiple-dose vial may not be used after 28 days of first puncture, unless its labeling specifies otherwise. The same FAQ adds two points:

  • The 28 days runs from first puncture, whatever the vial’s dating. USP separates it from the beyond-use date: a vial with a 60-day dating still has its 28-day limit from first puncture.
  • Multiple-dose is a tested status. USP chapter 659 defines a multiple-dose container as one whose contents have met antimicrobial effectiveness testing (USP chapter 51) or are excluded from it by FDA regulation. The preservative is what that testing checks.

On solutions made with the water, the Hospira label sets no holding time of its own. It says reconstituted solutions are not stored unless the manufacturer of the dissolved compound directs otherwise.

What do the label and a lot certificate show?

A label states what the maker intends; a lot certificate states what one tested sample held. The Hospira label for the 30 mL vial (DailyMed, revised 08/2019, NDC 0409-3977) gives these figures. Renovita Research also stocks that product as Hospira Bacteriostatic (BAC) Water-30ml (RESEARCH USE ONLY).

Label lineWhat it statesSource
NameBacteriostatic Water for Injection, USPHospira label
Preservative0.9% benzyl alcohol, 9 mg in each mLHospira label
pH5.7, range 4.5 to 7.0Hospira label
Container30 mL multiple-dose plastic Fliptop vial, polyolefin (an ethylene and propylene copolymer)Hospira label
Storage20 to 25 °C (68 to 77 °F), USP Controlled Room TemperatureHospira label
Lot and expiryPrinted on each vial labelHospira label
ConditionNot to be used unless the solution is clear and the seal intactHospira label

The certificate for Renovita Research’s 30 mL bacteriostatic water, lot EBC2610-RR-BWP-1005, reported on 10/06/2026, shows:

TestSpecification printedResult
Identity (LC-MS/MS)Conforms to declared compoundBenzyl alcohol, pass
Benzyl alcohol content9.0 mg/mL (0.90% w/v), plus or minus 10%9.20 mg/mL (0.92% w/v), pass
Heavy metals (ICP-MS)Under 10 ppmNot detected, pass
Bacterial endotoxins (LAL)Under 0.25 EU/mLNot detected, pass
Sterility (USP chapter 71)ListedNot tested

The same page names the vehicle as Water for Injection (USP), the appearance as a clear solution, and the container as a 30 mL plastic vial with a purple cap and silver crimp.

The benzyl alcohol result sits inside the limit the certificate prints, so the preservative strength is measured, not assumed.

The sterility row reads not tested: this lot was not put through the USP chapter 71 sterility test, so this vial is not described here as sterile.

The sample section reads “Client-supplied, verified at intake”, meaning the seller sent the sample in; the lot number is what ties the paper to a vial.

Does benzyl alcohol affect peptides?

Benzyl alcohol at 0.9% has made dissolved proteins aggregate in published studies, and every study below used a full-size protein. None tested a short research peptide, so the results describe proteins only.

StudyProteinWhat benzyl alcohol did
Roy et al. 2005, J Pharm ScirhIL-1ra, freeze-driedReconstituting with 0.9% benzyl alcohol in water gave more aggregation than reconstituting with water. How much depended on how well the protein’s structure survived freeze-drying. During room-temperature storage after reconstitution, it did not speed aggregation.
Zhang et al. 2004, J Pharm ScirhIL-1ra, in solutionIt bound weakly to the protein and shifted it toward partly unfolded forms that aggregate. Sucrose partly blocked this.
Lam et al. 1997, Pharm ResInterferon-gammaAt 0.9% it changed the protein’s tertiary structure and formed high molecular weight aggregates. The effect depended on protein, buffer and preservative concentration.
Bis and Mallela 2014, Int J PharmInterferon alpha-2aOf four preservatives tested, m-cresol caused the most aggregation, then phenol, then benzyl alcohol, then phenoxyethanol.

Two of the papers name a mechanism. Zhang et al. report a minor shift in tertiary structure toward partly unfolded species. Singh et al. 2010, Proteins, working on cytochrome c, trace the aggregation to partial rather than complete unfolding. Whether a given research compound behaves this way is not answered by any of them.

Frequently Asked Questions

Can you use sterile water instead of bacteriostatic water?

Sterile water for injection is the same water without the benzyl alcohol, and Hospira supplies it only in single-dose containers.

Does bacteriostatic water need to be refrigerated?

The Hospira label lists storage at 20 to 25 °C (68 to 77 °F), USP Controlled Room Temperature, and does not call for refrigeration. Renovita Research’s 30 mL product page lists controlled room temperature.

What is bacteriostatic water used for in a lab?

As research supply it is a laboratory solvent, used for dilution, solution preparation and analytical work, which is how the Renovita Research product page describes it.

What should a bacteriostatic water label show?

The name Bacteriostatic Water for Injection, USP; the benzyl alcohol strength (0.9% on the 30 mL vial); multiple-dose; a lot number and an expiry date. Hospira’s label adds that the solution should be clear and the seal intact.

Where to get bacteriostatic water for research

Renovita Research sells Bacteriostatic (BAC) Water-30ml (RESEARCH USE ONLY), with its lot certificate on the product page, on its lab supplies page alongside the Hospira 30 mL vial and its research peptides. Products are sold strictly for laboratory and research use only and are not for human or animal consumption. We ship only to addresses within the United States.

Shopping Cart

Before You Enter

Renovita Research products are sold strictly for laboratory and research use only. Please confirm the following before continuing.

Scroll to Top